Home > Drive Not > Windows Vista Dvd Driver Not Working

Windows Vista Dvd Driver Not Working


Med anvisningarna nedan kan du diagnostisera och lösa problem om CD-, DVD- eller Blu-Ray-enheten inte kan läsa eller identifiera skivor som du sätter in i enheten. Figure : Registry Editor: LowerFilters key If an UpperFilters value is also listed, select UpperFilters in the right window and press the Delete key. Verify computer running in 32-bit mode Windows 95 and Windows 98 users only Verify that your computer is running in 32-bit mode by clicking Start, Settings, Control Panel, double-click System, and Kontrollera att typen av skiva som du använder är kompatibel med enheten som är installerad på datorn. this contact form

Click Action, select Scan for Hardware changes, and then wait for Windows to find and install the CD/DVD drive. Install the updates according to the instructions on the download page. Do not use the Administrator User Account. Om du vill ha fler anvisningar klickar du på felsökningsstegen nedan.

Windows Vista Dvd Driver Download

Confirm the deletion by clicking Yes.. TechHelp SubscribeSubscribedUnsubscribe516516 Loading... Any advice would be helpful.Thanks.

  • Close Yeah, keep it Undo Close This video is unavailable.
  • If DVD/CD-ROM Drives is not in the list, skip to Step 2 to reset power or reseat the drive cables if necessary.
  • Click Uninstall a program in the Programs sections.
  • Ett specifikt uppspelningsprogram och codec måste installeras på datorn för uppspelning av DVD- eller Blu-Ray-filmer.
  • Try burning the disc at 4x before playing it from the computer.
  • Solutions System Restore To roll back these changes you can try restoring the system.
  • Figure : Ribbon and power cable Reinsert the power and data cables into the back of the drive making sure the cables fit snugly into their connectors and making sure there
  • I cannot load new software, play CDs or DVDs, and I am no longer able to burn music.
  • Click OK or Allow on any verification messages that open.

JIUJITSU2000 56,999 views 19:04 How to fix a DVD drive's tray that doesn't open or eject - Duration: 9:45. Reboot > shutdown and reinstall the device > reboot and see if windows starts searching for the drivers which you uninstalled above. NazmusLabs 386,312 views 16:05 How to Test & Fix Broken or Stuck CD/DVD Drive Tray - Duration: 21:38. Dvd Drive Not Detected In Windows 10 Step 1: Check the drive name in Device Manager If you can use the CD/DVD drive in Windows but your disc recording software does not work (such as Roxio Creator Basic),

Then reinstalled device and rebooted laptop, still problem persists. 3. Cd Drive Not Detected Windows 7 Intel Pentium Dual Core Processor with super multi DVD burner/labelflash with plenty of memory on both C and D hard drives.Here are the things I have done so far. Använd en förinspelad CD-, DVD- eller Blu-Ray-skiva beroende på vilken typ av enhet som är installerad på datorn. Om knappen är nedtonad fortsätter du med nästa felsökningssteg. Överst på sidan Kör Dell PC Diagnostics på den optiska diskenheten (CD-, DVD- eller Blu-Ray-enhet) Diagnostiken för optiska enheter kan kräva att

Select Computer in the main window. Dvd Drive Not Working Windows 10 Se till att du markerar kryssrutan Använd AutoPlay för alla medier och enheter. I dialogrutan Kör skriver du kontroll och trycker sedan på Retur. Wait 5 seconds for the computer to fully power off before turning it on again.

Cd Drive Not Detected Windows 7

Updated Windows and all the drivers Cleaned Registry Cleaned browser Histroy, Cookie & Temporary Files Ran Anti-Malware, spyware, etc. Will give that a go. Windows Vista Dvd Driver Download solvemyproblem 371,531 views 6:38 CD DVD drive not working - Duration: 7:52. Windows Vista Dvd Drive Not Found Solution My DVD/CD burner shows up in device manager, and reports no problems, but still doesn't read disks or let me upload software from a disc, and the Microsoft Fix-it says I

If Windows recognizes the drive, you are finished. weblink See the help section in the disc burning software that was used to burn the disc. Drive listed as working. With the 4D36E965-E325-11CE-BFC1-08002BE10318 key still selected, right-click any blank area of the right side of the registry editor window (the window pane listing all the values within the key). Windows Vista Cd Drive Not Reading Discs

Figure : Windows Recovery Options: Command Prompt Enter diskpart at the command prompt. Do the following depending on what is shown in the Device Status section: If error code 10, 19, 31, 32, 39 or 41 is shown inside Device Status, a problem exists Använd felsökningsanvisningarna nedan om CD-, DVD- eller Blu-Ray-enheten inte kan läsa eller identifiera några skivor. http://ict4m.org/drive-not/windows-vista-cd-dvd-driver-not-working.php Microsoft Windows Windows 10, Windows 8.1 och Windows 8 Microsoft Windows Windows 7, Windows Vista och Windows XP Överst på sidan Installera den senaste BIOS-uppdateringen på datorn Vi rekommenderar att du

Kim We could go back & forth for days, with me suggesting something and you saying already tried that, so not knowing what you have tried makes it senseless to comment. Dvd Driver For Windows 7 Click Start , and enter device manager into the Start Search field. You may have to restart the computer to complete the enabling process.

I have tried everything, spent hours and hours researching the web, even used Microsoft fixit center, they say the Drive is empty and I need to address the problem.

Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... If the CD-ROM does work from MS-DOS, this indicates that you have a corruption issue with Windows. Reports: · Posted 4 years ago Top Xhi Posts: 6298 This post has been reported. Cd Drive Not Working Windows 10 If a System Restore does not resolve the problem, you can use Recovery Manager to return the computer software configuration back to its original state.

Lighthouse - Unfotuntately I don,t have another machine to try the drive in. Additional information on bootable disks can be found on our boot disk page. After the CD/DVD software is reinstalled and the computer has been restarted, it should recognize the CD/DVD drive. his comment is here Autoplay When autoplay is enabled, a suggested video will automatically play next.

If Windows does not recognize the drive, repeat Step 1 to see if the drive name appears in Device Manager and troubleshoot disc burning software if needed.