Home > Xbox 360 > X Clamp Fix Fans Not Working

X Clamp Fix Fans Not Working

Contents

Vaughn Baker - January 1 Reply There are small black feet on the bottom of the fan assembly, You can push up from the bottom of the case if needed. If it is not how long does it last? When removing the last corner of the X clamp and holding the motherboard upside down, be sure to catch the CPU heat sink to avoid damage from it falling. Remove the clear and colored plastic backing material from all four thermal pads. More about the author

it's really simple if you follow directions.________________________________________Q. by overheating it you can remelt that solder and thus remake all the connections.I tried this out but it isnt workin for me ether you hav any other ideas pls email Cancel The All-New Pro Tech Toolkit The high performance electronics repair kit. You will insert the tool into the holes molded into the white plastic side case pieces.

Xbox 360 Overheating Repair

I bought the kit installed it after reflowing the xbox. please just read one step further and i will explain exactly how and why this works. « PreviousNext »View All Steps DownloadHey sorry but I live in Australia and pennies aren't On other occasions it might take a while, and you might find that the error code changes. Fantastic.

Two cables still connect it to the motherboard. Add a comment Add a comment Add Comment 1024 Step 41 GPU Heat Sink Edit Insert the tip of a small flathead screwdriver between the X clamp and its retaining post if it doesn't well there goes the cost of the kit, 30 bucks in shipping and an unhappy family. What To Do When Your Xbox 360 Overheats Conclusion To reassemble your device, follow these instructions from Step 42 in reverse order.

Watch QueueQueueWatch QueueQueue Remove allDisconnect The next video is startingstop Loading... Xbox 360 Rrod Repair You may also accomplish this task by using the edge of the Xbox 360 opening tool, but it may scratch the plastic case. The first two clips are located underneath the top vent closest to the faceplate, as shown in the pictures. Pry the X clamp away from its retaining post until it is lifted above the small groove cut into the retaining post.

my xbox instantly goes to 3 lights on start!! 03/06/2015 by Kush To fix it the right way, follow the instructions in this video, trust me it works. Xbox 360 X Clamp Fix Parts List Lowes This doesn't always work or last. In our case, we attached the CPU heat sink first. Your cache administrator is webmaster.

Xbox 360 Rrod Repair

Didn't see the comment about placing a piece of cardboard on the motherboard to prevent scratching until I had already screwed up my Xbox. Help? Xbox 360 Overheating Repair Add a comment Add a comment Add Comment 1024 Step 19 Edit Insert the flat end of a spudger and pry upwards to release the last remaining latch located above the Xbox 360 Overheating For No Reason Make note of how many quadrants are doing this.

These latches must be disengaged to separate the upper case from the console. my review here This will also prevent the red ring if you clean out your Xbox 360 at least once a month. garcialoic1 - 04/08/2014 Reply This RROD fix kit didn't work for me, sadly. Twist the screwdriver to fully release the X clamp from its retaining post. Xbox 360 Rrod Repair Kit

Be sure to position the heat sinks correctly before you stick them down, as the adhesive is extremely strong and sensitive to being repositioned. You're Finished! The other two error codes might call for a reflow of the CPU or GPU also, but is probably due to the dried up OEM thermal paste. click site Learn More.

Repeat this process for the fourth arm of the X clamp. 2 comments Is the x-clamp supposed to be reinstalled? Xbox 360 Overheating Fix 2 Red Lights Super easy to take apart, no problems except for two. GamerGuy51 230,622 views 11:12 Xbox 360 Ring Of Death How To Reset - Duration: 6:04.

It has been working for over an hour now so looks ok.

You may also use the long finger of an Xbox 360 opening tool to accomplish this task. I'm a retired Electronics Engineer and will be 80 in December this year. It's very simple to follow and clear. Xbox 360 Overheating But Not Hot the kit unfortunately didn't work.

Add a comment Add a comment Add Comment 1024 Step 28 Edit Orient the console so that the upper case is facing upwards. tez90, Oct 18, 2010 #2 miketrev Regular member Joined: Feb 1, 2009 Messages: 3,210 Likes Received: 0 Trophy Points: 46 Try and reflow it and get back to us if the Show more Language: English Content location: United States Restricted Mode: Off History Help Loading... navigate to this website Have you tried the Xbox 360 X-clamp repair?

Video Overview Step 1 Hard Drive Edit Grasp the hard drive assembly and press the release button while lifting its front edge.