Home > Xbox 360 > X Clamp Mod Not Working

X Clamp Mod Not Working

Contents

Can anybody help? Check out http://xbox-experts.com/e/tutorial.php?n=hybrid to read the entire tutorial. I just bought the new type heatsink from ebay for $7. This feature is not available right now. More about the author

These squares on the corners are the main improvement because the chip is taken under pressure equally not only in the center, the pressure that lasts on each solder ball is ELECTRICAL TAPE CAN CAUSE IT TO OVERHEAT, if it does that, use thinner tape, like the one I used in my tutorial, or the thermal compound method... 8.2) For those of When you power it on the next time it should work, if not you will have to try the next method that is given for your secondary error code. He then had to buy a new one.

Xbox 360 X Clamp Fix Parts List Lowes

Do the same for the CPU heatsink until both look like that: 6) Now cut a piece out of your phone/credit card and remove as much thermal compound as you can Up next X-Clamp-fix COMPLETE Guide - Duration: 9:55. Make sure that the layer is not too thick because this can result in problems later... Answer this question I have this problem too Subscribed to new answers Is this a good question?

Great job, man. =D
Thanks So much this works! This is basically a collection eight 12mm screws, and metal and plastic washers that are intended to replace the X-clamps on the CPU and GPU. Then put the heatsink back on, tighten it down decent, you don't need to crank it down, if its too tight it will just warp the board and you will be Xbox 360 Rrod Repair Kit Reply jim April 12, 2015 at 4:52 am There is something better then the " X clamp " it's called a Conformal compression assembly CCA , It's basicly a steel plate

I know some people imediately think that 8 pennys cannot fix an xbox hardware problem and now think my instructabe is ... 2 Step 2: And So Why Exactly Does This This is known as warpage or board flex, because looking at the board straight on it was curved and not flat the way it was meant to be. When we replace a Loading... Just in the case this doesnt fix it either you will have to use a little trick which is called "baking".

The solder would crack underneath causing loose connections. How To Fix Xbox 360 Red Ring Of Death Permanently The music was chosen and cut by humboldt think he did a great job on that as well sounds pretty cool. NOTICE: The main goal to ACHIEVE is a leveled motherboard.. Did you have success?

X Clamp Fix Xbox 360 Slim

Read More ! EricTheCarGuy 1,732,967 views 26:57 XBOX 360 Repair Guide - #2 Preparing for the X-Clamp Fix - Duration: 9:59. Xbox 360 X Clamp Fix Parts List Lowes Close Yeah, keep it Undo Close This video is unavailable. Xbox 360 Xclamp Fix Parts List Never toweled, opened or anything before.

You will NEVER get that off. http://ict4m.org/xbox-360/x-clamp-fix-fans-not-working.php Any of these chips can cause the RROD and sometimes has nothing to do with a BGA chip but can be resistors, capacitors, mosfets, or other electrical components as well as I did the X-Clamp on my buddy's 360, and it worked for 15min, then got the RRoD again. Sooner or later this results in a cold solder joint or even a bridged solder joint(short) under one of the chips which can cause the ROD... 3) Now take the screwdriver Xbox 360 Rrod Repair

Christian Cawley October 14, 2014 14-10-2014 5 minutes Xbox 360 RRoD X-Clamp Fix – Does It Work? There was little information about why the Xbox 360 game consoles would RROD, eventually after a long drawn out process Microsoft started repairing or replacing these consoles under an extended due Of course without the right equipment, those attempting this X Clamp FIX have no idea that they are actually causing harm to their console they are in fact trying to fix. There click site Is your device still working?

Sign in Loading... Xbox 360 X Clamp Removal Rob Papallo 276,252 views 39:51 X-clamp replacement why you should never do it! - Duration: 14:16. If you have Gen 1 XBox 360 then you should while using the xclamp kit buy the new heat sink (easy to find).

xclampkit 34,164 views 8:50 Fix Red Ring of Death Xbox 360 - Duration: 20:36.

The eight screws and the washers make a better job of things. Just don't try Perma-Seal. No X-Clamps or towles required! Xbox 360 Red Ring Of Death Fix Without Opening Repair Red Lights of DEATH! - Duration: 11:12.

I redid the whole X-Clamp fix and it worked! These squares on the corners are the main improvement because the chip is taken under pressure equally not only in the center, the pressure that lasts on each solder ball is This doesn't always work or last. navigate to this website X Clamps Recent blog posts view Why XModdz LLC closed by XModdz view Want to buy a BGA Rework Station?

THIS IS IT!!!(Note: this fix requires you to open the console, THIS WILL VOID YOUR WARRANTY! I got a second machine, older model (2006) and did the same fix and it went from 3 red lights down to 2 when turned on.