Home > Xbox 360 > Xbox 360 Cpu Fan Not Working

Xbox 360 Cpu Fan Not Working

Contents

Lift the right case off by its metal framework. TripAcesFull 1,880,157 views 5:51 Xbox 360 12V Fan Mod/Upgrade (NO SOLDERING) - Duration: 13:09. As far as future maintenance, it doesn't sound like you necessarily overheated your system, but that it just finally went out. Anyone want a perfectly working Xbox 360S with a drive the spins game discs upon ejection? click site

Demon10000, Jul 25, 2008 Demon10000, Jul 25, 2008 #9 Jul 25, 2008 #10 Psychotext [H]ardness Supreme Messages: 5,897 Joined: Mar 21, 2005 RRoD is a general hardware failure. Add a comment Add a comment Add Comment 1024 Step 2 Edit Orient the console so that the words "XBOX 360" on the sides are right-side up, and the faceplate is Add a comment Add a comment Add Comment 1024 Step 28 Edit Continue to hold the cases apart to prevent the clips from reattaching. There is a locator peg underneath the fan duct (top right corner of the fan duct as viewed in the pictures).

Xbox 360 Fan Not Spinning Fix

Please try again later. You're Finished! Lift the left edge of the bottom bezel up enough to gain clearance.

Just make sure you don't break the springs for the USB bay area. While pushing the left and right case away from each other with one hand, pry the clips away from the case with a metal spudger. Lift the hard drive cable connector off the hard drive bracket. Xbox 360 Fans Don't Spin Aluminium 220 8.

Be sure to rotate the spudger far enough so that the plastic clips clear the silver rim of the top bezel. Xbox 360 Fan Replacement As long as you have your serial number, you should be fine. Add a comment Add a comment Add Comment 1024 Step 15 Edit Use the tip of your spudger to release the clip on the top vent nearest the back of the Andrews Arcade 1,575,552 views 11:40 How to open and properly clean an Xbox 360 Fat - Duration: 36:06.

Luposian - 03/09/2014 In regards to davidgardner301 comment there is a extra step they. Xbox 360 Fan Wont Turn On iirc yeah - it's caused by heat in the first place, so pre-emptive measures can probably -prevent- a RROD. To avoid ESD damage, be sure to lay your logic board on a soft, static free surface during service. At this point I recommend that you use this kit.

Xbox 360 Fan Replacement

There is a locator peg underneath the fan duct (top right corner of the fan duct as viewed in the pictures). Add a comment Add a comment Add Comment 1024 Step 32 Faceplate Edit Orient the console right-side-up, with the faceplate facing forward. Xbox 360 Fan Not Spinning Fix Insert a metal spudger through the rear-most slit on the right edge of the top bezel and between the bottom edge of the clip and the right case. Xbox 360 Slim Fan Not Working weitmeyerj - 04/22/2011 Reply The correct size is T8!

Tossed out your old disk drive Eric Liu - 05/05/2014 Reply So I installed the drive but the thing keeps reading the games as dvds, hence; wont play them, why? get redirected here Add a comment Add a comment Add Comment 1024 Step 22 Edit This clip does not have a slit in the bezel to guide you. Please upload a file larger than 100x100 pixels We are experiencing some problems, please try again. Add a comment Add a comment Add Comment 1024 Step 7 Edit Remove the bottom vent from the 360. Xbox 360 Fans Not Working 3 Red Lights

Add a comment Add a comment Add Comment 1024 Step 37 Edit Remove three 5.6 mm T8 Torx screws securing the RF module to the metal chassis. Add a comment Add a comment Add Comment 1024 Step 14 Edit To release the clips, work from the middle of the top vent. Add a comment Add a comment Add Comment 1024 Step 31 Edit Grab the power connector by its cables and pull it straight out of its socket on the optical drive. navigate to this website Preview my answer Post my answer View Statistics: Past 24 Hours: 6 Past 7 Days: 29 Past 30 Days: 144 All Time: 13,980 22,633 Free Manuals 89,574 Solutions 6,855 Devices iFixit

junkyardjojo - 07/16/2014 Reply Is the rf module married to the mother board? Xbox 360 E Fan Not Working Be careful not to damage the sockets as you rotate the motherboard away from the metal casing. Rating is available when the video has been rented.

After this I placed the screws into the holes, then a washer on the screw, then the motherboard, and then the heat sink.

Your Microsoft warranty for any components not directly attached to the logic board will likely be voided by removing this seal. It will take some force to pull the hard drive out. 2 comments If i buy a new xbox 360 and replace the hardrive inside with my own, will i have Conclusion To reassemble your device, follow these instructions in reverse order. Xbox One Fan Not Working I answered "NO." The Xbox 360 has a great library of games but it's backed up by some cruddy hardware engineering.

Simultaneously rotate the spudger away from the console and pull up on the top bezel to free the clip. Vaughn Baker - January 1 Reply There are small black feet on the bottom of the fan assembly, You can push up from the bottom of the case if needed. Do not completely remove the dual fan assembly yet. http://ict4m.org/xbox-360/xbox-game-not-working-on-xbox-360-update.php Up next How to take apart and open Xbox 360 Slim - Duration: 11:40.

This can also be accomplished using an Xbox 360 opening tool. When removing the last corner of the x clamp and holding the logic board upside down, be sure to catch the CPU heat sink to avoid damage from it falling. Add a comment Add a comment Add Comment 1024 Step 15 Edit Orient the Xbox 360 S so that the hard drive port is facing up and the faceplate is facing Simultaneously pull the bottom bezel up and rotate the spudger away from the console to free the clip.

Insert a spudger between the right and left cases to hold them separate while you work elsewhere. Add a comment Add a comment Add Comment 1024 Step 19 Edit Insert the flat end of a spudger and pry upwards to release the last remaining latch located above the Xbox 360 failure rate? (this question is mostly for playstation fans)? Rotate the spudger upward to release the last clip.

Rotate the spudger away from the console, prying the edge of the fan vent up until the two plastic clips come free. matt337 - 12/14/2012 Reply Add a comment Add Comment 1024 Step 38 Edit Grasp the RF module and lift it straight up to disconnect it from its socket on the motherboard. Be sure to rotate the spudger far enough so that the plastic clips clear the silver rim of the top bezel. Also, try to avoid playing your Xbox for more than a few hours at a time, and allow ample time for the console to cool down between playtime.

Slide the locking tab on the power switch board cable connector toward the top of the console. Cancel: I did not complete this guide. 41 other people completed this guide. There are website regarding this procedure if you want to look it up. You might want to post an images with your question.

Replacing the fans on a RROD'ed console isn't going to make a difference.Click to expand...