Rob Papallo 276,252 views 39:51 EASY FIX ROD XBOX 360- 3 red light reset - Duration: 6:05. Can someone tell me how to fix this or at least not get the RRoD prodigee, Jul 25, 2008 prodigee, Jul 25, 2008 #1 Jul 25, 2008 #2 pigpen 2[H]4U One comment Be careful not to lose or break the two teeny metal clips securing the optical drive assembly snugly to the metal casing on either side of the drive's front Loading... click site
Joe Begley - 02/08/2011 Reply Super easy as long as you have that tool and follow the directions. If the eject button still doesn't work, your disc drive may need to be replaced. pigpen, Jul 25, 2008 pigpen, Jul 25, 2008 #8 Jul 25, 2008 #9 Demon10000 [H]ardness Supreme Messages: 4,502 Joined: Aug 20, 2006 pigpen said: ↑ Maybe i am misunderstanding, but it One comment I found it easier to open these clips using the pointy end of the spudger rather than the flat end.
So now plug her in. It's very simple to follow and clear. Just make sure you don't break the springs for the USB bay area. Carefully release the fan duct retaining clip and remove the fan duct from the Xbox.
E67: Hard Drive Error - Hard drive timed out during reset. No X-Clamps or towles required! The console will still power on, and should display an error code on the screen it is connected to. Xbox 360 Fans Don't Spin Even though the console will not turn on, you can obtain a secondary error code from it.
Having never opened the xbox before I was able to do this in 15 min. You can find out which issue the console is really having. The opening logo comes on the screen and the green light come on, then the fan starts to continuously increase in speed until the two red lights come on. 12/13/2015 by Use as little tape as possible 6 Step 6: Put It All Together 7 Step 7: OVER HEAT!!!!this is the step most people who fail at this method seem to miss.overheat
If you are reassembling your Xbox 360 after installing the Red Ring of Death Fix Kit, the eight T8 Torx screws circled in orange are not reused. Xbox 360 Overheating Fix Push the upper and lower cases apart to fully release the retaining clips. WARNING: Adding a new hsf to the gpu will result in not being able to put the dvd drive back in. IIRC, the RROD error is caused by heat -- and fans not spinning causes heat.
Otherwise, before buying a new drive, try cleaning the inside of the old one and/or replace the belt involved in opening and closing the drive door. - Good Luck Eric - Darryell Fish - October 8 Reply i have a xbox 360 s.When i push the button it only beeps.I bought a new power supply and rf module and it still wont Xbox 360 Fan Not Spinning Fix Once I find a good place for it, I will post it. Xbox 360 Fans Not Working 3 Red Lights I used a spudger to press in the topmost tines on these clips because they were catching on the drive and bending up.
should i try overheating it again? get redirected here thanks for the info fella ;)))) I do have one question. This should be the first thing to try because that's probably the only thing wrong with the Xbox 360. volkswagon2 - October 15 Reply My Xbox got wet a little bit let dry out and turned on it did ventilation message turned off and won't turn on again Heather Tew Xbox 360 Slim Fan Not Spinning
While pressing down on the tool, push the lower and upper cases apart to separate the retaining clips. 2 comments I didn't have an XBox tool, so I followed instructions in The most common issue is a cracked or cold solder joint underneath the GPU on the motherboard. Corresponding error codes¶ To determine which error message corresponds to your secondary error code, use the error code database provided by Xbox-Experts. navigate to this website Forren - 06/17/2014 I found that inserting a sprudger between the X clamp and retaining post and turning while lifting worked well without damaging the board Patrick Kremer - October 22
Thanks for the great instructions! Xbox 360 E Fan Not Working Hope this can also help you all. Add a comment Add a comment Add Comment 1024 Step 15 Edit Use the tip of your spudger to release the clip on the top vent nearest the back of the
deff the best info ive seen on the net. If the problem is the CPU, GPU or RAM like you mentioned im most likely [email protected]#$ outta luck because I dont have the knowledge to fix it myself and dont want and are ready to throw it all away///////////////// karen - 06/12/2014 Reply please help me. Xbox 360 Overheating But Not Hot The small flathead screwdriver included with the kit is too small and weak to do the job.
E70: Hard Drive Error - Hard drive not found by console. With a liquid flux, a dual digital thermometer etc.. Up next How to open and properly clean an Xbox 360 Fat - Duration: 36:06. http://ict4m.org/xbox-360/xbox-game-not-working-on-xbox-360-update.php if your warranty is still valid, just send your xbox to Microsoft.) Step 1: So What Is It??Show All Items This is known as the penny fix.
Before reinstalling the GPU heat sink, be sure to apply a new layer of thermal paste. Loading... Just slide it in against the side of the case and the clip will pop off. Its cable is still attached to the motherboard. 4 comments Cleaning out the fan now, will help problems in the future.
I got the same pic and Firebert has every right to see it be that changed or at least give him credit for the use of it.your a good sport tenThank Add a comment Add a comment Add Comment 1024 Step 8 Faceplate Edit Insert the edge of a spudger between the faceplate and the outer casing near the power button. If the drive can eject, read, and write discs in Windows, but causes an error code on the console, replacing original firmware should fix the issue. Pry the front edge of the bottom vent away from the faceplate. 2 comments You can avoid this step by pulling the front cover off.
which 2 lights are red out of the 4 means something different each time 02/22/2011 by pollytintop Add a comment 0/1024 Cancel Post comment Are you sure you want to delete It will speed up and slow down the fan speed based on temperature. If the RROD is already plaguing your Xbox, and your console is no longer covered by Microsoft's warranty, there is hope yet. The holes barely matched up with the old gpu heatsink holes.
ThioJoe 2,009,049 views 5:20 Xbox 360 fat version replacing the heat sink compound tutorial. Mix Bag 262,609 views 4:50 Repairing The Red Ring of Death XBox 360 - EricTheCarGuy - Duration: 26:57. The heating process will not damage the heat sinks in any way. I prefer a constant 12v source that will keep the fans running at a high rpm all the time.
The possible courses are: Incorrect mains voltage - If the power supply is plugged into a mains supply, that is at a different voltage to what the power supply is rated when i turn it on to over heat it just sits there and blinks with the RROD not getting hotter or anythingOpen it back up and unplug the fan. Four rapidly flashing quadrants = a numerical 0 Three rapidly flashing quadrants = a numerical 3 Two rapidly flashing quadrants = a numerical 2 One rapidly flashing quadrant = a numerical i am no expert but i do fix just about anything that is broken.
IS taking the RF off really necessary? Grasp the back portion of the lower case and lift it upwards to separate it from the console. One comment Does anyone know if the Silver Tape is Lead Tape?